European Journal of Prosthodontics

SHORT COMMUNICATION
Year
: 2016  |  Volume : 4  |  Issue : 3  |  Page : 60--61

A simple technique for making the final ocular impression


Sunil Kumar Mishra1, Ramesh Chowdhary2, Srinivasa B Rao3,  
1 Department of Maxillofacial Prosthodontics and Implantology, Peoples College of Dental Sciences and Research Centre, Bhopal, Madhya Pradesh, India
2 Department of Maxillofacial Prosthodontics and Implantology, Rajarajeshwari Dental College, Bengaluru, India
3 Department of Maxillofacial Prosthodontics and Implantology, Gitams Dental College, Visakhapatnam, Andhra Pradesh, India

Correspondence Address:
Sunil Kumar Mishra
Department of Maxillofacial Prosthodontics and Implantology, Peoples College of Dental Sciences and Research Centre, Bhopal, Madhya Pradesh
India

Abstract

Different impression techniques have been given in literature for the fabrication of ocular prosthesis. An accurate impression is required for the perfect fitting of the prosthesis. This article describes a modified impression with the help of dispensing gun with simple, accurate and time saving technique.



How to cite this article:
Mishra SK, Chowdhary R, Rao SB. A simple technique for making the final ocular impression.Eur J Prosthodont 2016;4:60-61


How to cite this URL:
Mishra SK, Chowdhary R, Rao SB. A simple technique for making the final ocular impression. Eur J Prosthodont [serial online] 2016 [cited 2019 Mar 21 ];4:60-61
Available from: http://www.eurjprosthodont.org/text.asp?2016/4/3/60/207365


Full Text



Various impression techniques had been suggested for making the ocular impressions.[1] Brown [2] suggested syringe technique and Jethwani et al.[3] suggested hollow handle technique for making impression, but drawback with this techniques was that the impression materials had to be loaded in the syringe before making impression. This article describes a simple, accurate, and time-saving technique, where the impression can be made directly with the dispensing gun using mixing tip without the need of attaching and loading the syringe.

 Procedure



Make the primary impression of the defect with putty consistency addition silicone (Reprosil, Dentsply, Milford, USA) impression material, and pour the impression with type II dental plaster (Kalabhai, Mumbai, Maharashtra, India)Fabricate the special tray with cold cure clear acrylic resin (DPI, Mumbai, India) and make escape vents for the escapement of excess impression materialAttach a mixing tip (Reprosil, Dentsply, Milford, USA) to the special tray [Figure 1]aPlace the special tray in the ocular socket for making the final impression of the ocular defect. Connect the dispensing gun (Heraeus Kulzer, Dormagen, Switzerland) to the mixing tip attached to special tray and inject the impression material (Regular viscosity addition silicone, Reprosil, Dentsply, Milford, USA) [Figure 1]bThe patient was instructed to do ocular movements to get functional impression of the socket. Removed the impression and checked for its accuracy [Figure 2].{Figure 1}{Figure 2}

Declaration of patient consent

The authors certify that they have obtained all appropriate patient consent forms. In the form the patient(s) has/have given his/her/their consent for his/her/their images and other clinical information to be reported in the journal. The patients understand that their names and initials will not be published and due efforts will be made to conceal their identity, but anonymity cannot be guaranteed.

Financial support and sponsorship

Nil.

Conflicts of interest

There are no conflicts of interest.

References

1Shenoy KK, Ratna Nag PV. Ocular impressions: An overview. J Indian Prosthodont Soc 2007;7:5-7.
2Brown KE. Fabrication of an ocular prosthesis. J Prosthet Dent 1970;24:225-35.
3Jethwani J, Jethwani GS, Verma AK. Functional impression technique for an ocular prosthesis. J Indian Prosthodont Soc 2012;12:55-8.